View source for OLPC Firmware q2c17

{{OLPC}}
== OLPC Firmware Release q2c17 - 2007-06-08 ==

This firmware is a release candidate for the '''BTest-4''' built.  It will also work on all board s except pre-B1.  Do not use it on pre-B1 boards - it will brick them because of the EC microcode.

<big><font color="red">'''BIG FAT WARNING!'''</font></big>
'''The manufacturing data has moved locations.  If you are upgrading from the B series of the firmware the manufacturing data will be moved to its new location.  After that has happened you must not install anything from the B series of the firmware.  If you do then <u>you will erase</u> your manufacturing data.'''
<br>
----
Download: [http://dev.laptop.org/pub/firmware/q2c17 q2c17]
----

====<font color=red>How to get the ok prompt</font>====
[[Image:Power-button.jpg|thumb|right|Power & Game buttons]]
Press the "X" (down) game key after hitting the power button to enable the ok prompt.  You still have to press the ESC key (upper left on the keyboard [[Image:Key esc.jpg]]) during the countdown.  If you don't press the "X" game key, the firmware goes into fastboot mode, in which:
* The keyboard is not probed, thus saving some time
* The USB bus is not enumerated, thus saving even more time
* The boot order is SD, NAND, wireless
* OFW does not put any text on the screen, just graphics
* When transferring control to the kernel, OFW freezes the screen using the DCON, which hides the Linux console text until Linux unfreezes the DCON.  The intention is to migrate to a "pretty boot" scheme where there is no scrolling text in the normal boot case.

In some previous firmware versions, pressing any game key would get you to interactive mode; in this version, only the "X" game key, which is the one nearest to the power button, does so.

====How to play the startup sound====
The startup sound was annoying developers, who reboot frequently, so it is no longer automatic.  To play it, after you press the power button, press the small button that is on the other side of the display, across from the power button.

=== Changes since [[OLPC Firmware q2c16]] ===

=== Open Firmware is r444 ===
* Remove WLAN RESET workaround
* fixed battery init commands. 

=== EC code is PQ2C17 ===
* Enable Output driver for WLAN_RESET# signal.
* Implement command 0x22 (EEPROM Initialize) for GoldPeak LiFePo4 batteries.

=== Installation Instructions ===
* '''If you have a B1 or B2 system:''' 
** Detailed upgrade instructions are located [[Upgrading_the_firmware|here]].
** If your firmware version is earlier than the version in [http://wiki.laptop.org/go/Autoreinstallation_image Auto Install Image] then you can just use that procedure for the update.<br>  ''Note:'' that this procedure will also upgrade the image in your nand flash -- which is the entire Linux operating system and all the files you may have edited or saved.  '''This means it will ERASE what is in your nand and re-write it.'''  So you will lose any data you have stored on the filesystem unless you back it up.  If you do not want your files erased, then please use the [[Upgrading_the_firmware|first procedure above]].
** Do '''NOT''' use olpcflash to write new firmware images.  Doing so will erase the manufacturing data that was added at the factory.
** After you reflash, you must power cycle by physically removing power from the system.  A warm-start or button-induced restart is not sufficient.  Please remove both the battery pack and wall adapter for 10 seconds.

* '''If you have an ATest system'''
** If you use olpcflash to write this image, you must use the --brick option.<br> Example: <code>olpcflash --brick -w image.rom</code><br> The --brick option makes olpcflash update your EC code as well as the firmware.

[[Category:Firmware]]